Quick Answer: Blink splits into two completely different reset paths depending on the model. The Mini, Mini 2, and Wired Floodlight Camera connect straight to Wi-Fi and each has its own reset button — hold it for 10 seconds until the LED blinks red then blue. Battery-powered cameras that depend on a Sync Module (Outdoor 4, Outdoor/Indoor 3rd Gen, XT2/XT, 1st-Gen Indoor, Battery Doorbell 2K+) have no reset button of their own, per Blink’s own troubleshooting documentation — you either reset the Sync Module (unplug, hold its rear button, plug back in while holding for 5 seconds) or delete and re-add the individual camera in the Blink app. Either path leaves cloud-saved video history on your Blink Subscription Plan untouched, since it’s tied to your account, not the hardware.
Figuring out which path applies to your camera is the whole trick here — trying to find a reset button that doesn’t exist on a Sync-Module camera is the most common reason people get stuck.
Does your camera have its own reset button?
| Model | Connects via | Has its own reset button? |
|---|---|---|
| Blink Mini / Mini 2 | Direct Wi-Fi | Yes — back of the camera |
| Wired Floodlight Camera | Direct Wi-Fi | Yes — top of the camera |
| Video Doorbell (1st Gen), Wired Doorbell 2K+ | Direct Wi-Fi | Yes — on the unit |
| Outdoor 4, Outdoor/Indoor 3rd Gen | Sync Module | No — reset via Sync Module or app |
| XT2 / XT, 1st-Gen Indoor | Sync Module | No — reset via Sync Module or app |
| Battery Doorbell 2K+, Video Doorbell (2nd Gen) | Sync Module | No — reset via Sync Module or app |
This split matches our Blink camera offline guide’s Sync-Module-requirement breakdown — the same models that need a Sync Module to get online in the first place are the ones with no built-in reset button.
How to reset a Blink Mini, Mini 2, or Wired Floodlight Camera
- Find the reset button — the back of the camera on a Mini or Mini 2, the top on a Wired Floodlight.
- Press and hold for 10 seconds. The LED blinks red, then switches to blinking blue.
- Blinking blue means pairing mode. The camera dropped its Wi-Fi credentials and is ready to be added as new in the Blink app.
- Re-add it in the app, rejoin it to your 2.4GHz network, and rebuild any motion zones or schedules — none of that carries over through the reset.
A short press under 5 seconds on the Wired Floodlight Camera does a lighter restart instead — it clears temporary glitches without wiping Wi-Fi credentials, so try that first before the full hold.
Blink Mini 2
- Worth considering as a straightforward replacement if a reset doesn't bring an aging Mini back.
- Color night vision and a built-in spotlight outclass the original Mini.
- Same setup flow as the camera you're replacing, so there's no new system to learn.
Managing Blink cameras across a small office instead of a single home? A free Amazon Business account unlocks quantity discounts and tax-exempt purchasing if you’re replacing more than one unit at once.
How to reset a Blink Sync Module (and the cameras attached to it)
- Unplug the Sync Module from power.
- Press and hold the reset button on the back (next to the USB port on a 1st-Gen unit) using a paperclip or similar thin object.
- Plug it back in while still holding the button, and keep holding for a full 5 seconds.
- Release when the LED blinks red. Let it finish cycling through its light sequence.
- Wait for blinking blue plus solid green — per Blink’s own support documentation, that’s your confirmation it’s back in setup mode and ready to be added again.
- Delete the Sync Module in the Blink app and reinstall it from scratch. Every camera that was paired to it goes offline the moment you start step 2 and has to be re-added one at a time afterward.
Resetting the Sync Module is disruptive by design — it takes down every camera on that hub, not just one. If only a single battery camera is misbehaving, skip straight to deleting and re-adding just that device in the app instead.
Blink Sync Module 2
- Worth keeping a spare on hand if a reset doesn't bring a Sync Module back — a dead hub takes every paired camera down with it.
- Swapping in a fresh Sync Module is faster than troubleshooting a flaky one for hours.
- Compatible across the same generation lineup, so existing cameras re-pair without buying new hardware.
Deleting and re-adding a single camera (no Sync Module reset needed)
If the rest of your system is fine and only one battery camera is stuck, there’s a lighter option than resetting the whole Sync Module:
- Open the Blink app and select the misbehaving camera.
- Choose Delete Device to remove it from your system.
- Tap the + icon to add a camera, and follow the in-app pairing flow to re-add it to the same Sync Module.
This re-pairs just that camera without dropping the rest of your system offline, and it’s the closest equivalent Sync-Module cameras have to the Mini’s built-in reset button.
It’s not just Blink
Ring, Nest, Arlo, and Wyze all draw a similar line between a light restart and a full factory reset, though the exact mechanics differ — our how to reset a Ring camera guide covers the equivalent breakdown for that brand. If a reset doesn’t fix what’s actually wrong, our Blink camera offline guide covers the Wi-Fi signal and Sync Module connectivity issues that cause most “won’t reconnect” problems a reset alone can’t solve.
The bottom line
Check which category your camera falls into before hunting for a button that might not exist: Mini, Mini 2, and Wired Floodlight have their own reset button (hold 10 seconds, or under 5 for a lighter restart on the Floodlight); every Sync-Module-dependent battery camera resets through the hub itself or a simple delete-and-re-add in the app. Cloud video tied to your Blink Subscription Plan is never at risk from either path. Still offline after a proper reset? Our Blink camera offline guide covers the signal and Sync Module fixes that solve what a reset alone can’t, and our best Blink camera guide is the next stop if the hardware itself turns out to be the real problem.